Chevrolet Colorado & GMC Canyon Forum banner

Mod Meet @the Busted Knuckle - May 16th - Clarksville, TN

13520 Views 252 Replies 23 Participants Last post by  rshadd
Alright guys, it's official. I am going to host the mod meet at my house on the 16th.



Where:

When: May 16th, 10 AM - when everyone goes home

What to bring: Truck, Mods and happy faces

Food will be provided. Usually grille some burgers and hotdogs and have soda (pops) like Coke, Pepsi, Mountain Dew, etc. I am fine if you want to BYOB but there won't be much drinking going on since we will be working on the trucks. No need to get snookered and mess up someone's truck, then drive home...

PARKING: This is kind of important due to the location of my house. The red areas are able to be parked in. With the current plan, I will have my truck in the garage, (since I can stage it there before hand) and then 4 more trucks in the driveway. This will give us plenty of room to run the jack around it. Park in the driveway if you have work to be done. We can easily shuffle trucks around once one is complete. If you do not have any work, or are "in line" then please park in one of the red locations, just stay away from the curve in the road.



Things we could use:
Pop up tents (I have one)
fold out chairs (I have a few)
any special tools for the planned mods
any special food you want to bring

List what you plan to bring and I will add it below:

Who's coming and what mods are they bringing:
1. Blurred - Boyd - Thermostat replacement, swap to 2" blocks, add a spacer or two on the front shocks, possibly replace stripped lug bolt.
2. Kerad11 - Darek
3. T-bone - Tom - Flare besides and switch blocks, Rear shocks, Put rear on bumpstops
4. Yehaw404 - Dennis
5. HellOnWheels - Dawn
6. Tweek - Vernon - Looks like it will be just graphics on mine...
7. 05crewi5 - James + 1 - air-bagit notch, I have basically the whole front end, but I want to get the notch done., I'll bring what I have just for fun
8. Wtracing - Ricky
9. Minitruckin9509 - Nathan - gutted manifold install
10. Colorado zq8 - David - jack stands
11. Mwcky2204 - Mark - Id like to see if we can swap out the OEM fogs for some LED 7" pods I picked up.
12 Kaylyn - Mark's minion - Install 2.25 coil spacers and .25 ball joint spacers on Kaylyns truck, swap wheels and tires (hope they fit) :noes:, swap her dome light for a Supermod with a kill switch.
13. arickus - A.J.
14. 07ColoradoBLK - Alex
15. Charliebrown001 - Carter
16. Matt shadow - Matt
See less See more
2
221 - 240 of 253 Posts
I have an extra S10 overhead console if someone wants it. It's the long one, good for extended or crew cab.

Cheap, value meal cheap
I'll take it if no one else needs it. Pretty sure I can use it.
If three will be plenty, I won't bother getting one and I'll take that deal.

Fold out table already in the bed,
@blurred thinking of bringing hotdogs or meat or something to help out with food. Any ideas? Forgot if you said the grill would be going or not..

Also, was thinking about the welder I'm bringing. Do you have a plug in for a 220?

I think that's all I can think of right now. Man it's late.



Sent from AutoGuide.com Free App
No need to bring food unless there's something special you want. O have burgers and dogs and chips and cokes and mountain dew.
I have a 220 plug. It's for the dryer but it's 220 lol
Bunch of lucky bastards. I'm stuck here in Florida and have to work tomorrow. :anger: :mad3:
@05crewi5 this is the plug for it

See less See more
Also, we are going to need an extension cord that can handle 220. I'm sure your welder isn't a110

Dang. I left it at the shop. No way to get it now, can't believe I didn't think of that... The one I had would have reached everyone where they parked lol.


Sent from AutoGuide.com Free App
@05crewi5 this is the plug for it


Can't see it
Edit* nvm I can now

Sent from AutoGuide.com Free App
Auto part Bumper Hand Vehicle door Finger
@blurred will this be a problem...


Sent from AutoGuide.com Free App
See less See more
Doesn't look like it will be a problem. Problem will be the cord length though. Lol let me go look at the plug again.
The gap between the top center pin and the side pins is about the size of a nickel. If that helps any
Anyone looking for a stock airbox? Room Floor Machine


Also have brand new carpet for a single cab 88-93 s10 light grey in color. BRAND. NEW. please buy it waaahhh






..lol

Sent from AutoGuide.com Free App
See less See more
The gap between the top center pin and the side pins is about the size of a nickel. If that helps any

Sounds like it'll work fine :)
Also the clamps have long cords so it shouldn't be too bad...? Lol


Sent from AutoGuide.com Free App
It's also only a 30 amp fuse.
It's also only a 30 amp fuse.

I've got the hardware that came with the notch to bolt it in place and I can weld it when I get home if need be :)


Sent from AutoGuide.com Free App
I made it to oak grove. See you guys in the morning.

And alex is at Dareks already.
I made it to oak grove. See you guys in the morning.



And alex is at Dareks already.

How far are you guys coming?


Sent from AutoGuide.com Free App
Well I'm a step ahead with the projects, just got done changing my oil. This was the first time I ever tried HyperLube additive, that stuff is thick as honey.
If anyone wants to grab breakfast in the morning, I'm thinking of hitting up Shoney's on the way into town. Maybe 9am.
If anyone wants to grab breakfast in the morning, I'm thinking of hitting up Shoney's on the way into town. Maybe 9am.
Should be arriving around then - I'll be looking out.
Also if anyone's got some welding gloves, please bring some cause I apparently lost mine. Lol


Sent from AutoGuide.com Free App
Can't find welding gloves, not even in other, other shed. Gonna have a talk with the kids when I get back...
On my way, got pushed back a bit since the rain down here is worse than they said it would be. I need a bed cover lol but I got some tarps on


Sent from AutoGuide.com Free App
221 - 240 of 253 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top