well for some reson now when i try to use the RS nothing happens, no cluster lights or anything??

can anyone tell me what you have to do to get a remote start to work on these trucks?

 

apology for making this thread up. I'm looking to change my ignition wire set and can not find which model fits mine.. Does anyone has experience or knowledge what set would fit? any response is highly appreciated.

 

the OP is from 2008

floydpo wants to know......

 

I can help you, I wired in a remote start on mine, I am very good with wiring.

I think you don't have your tach signal hooked up or learned? Do you have the tach signal from the remote start unit "usually purple" hooked to pink injector wire or alt. wire or coil wire, for a tach signal?

Ounce hooked up you will need to star the truck the normal way, and follow your remote start instructions for learning the engine running/on/tach signal.

Without this it may attempt to start ie ignition, accessory , lights on dash, than off on again.

Also do you have the ground-out when running signal from the remote start unit hooked up to the bypass module??

also when it fails to start it should flash the lights or chirp a number of times indicating a fault code, count the flashes chirps, and look it up in your install manual.

let me know how you make out, if you need fast assistance, pm for my phone number, i'm off injured right now and bored, so i don't mind to help

 

does the security light go out when it attempts to start or does it flash?

 

This is one thing I will pay someone to do for sure!

 

Your truck is a 2007 so it is different than mine the info below is for a 07 colorado

-you need the accessory voltage from the remote start unit hooked to WHITE/RED to BROWN (+) IGNITION SWITCH

- the ignition from the remote start unit to WHITE/GREEN to DARK BLUE (+) IGNITION SWITCH HARNESS


hope this helps





12 VOLT CONSTANT


GET 12VOLTS FROM VHICLES BATTERY ONLY


@ BATTERY ONLY

STARTER not used! See NOTE *1
STARTER 2 N/A
IGNITION 1 WHITE/GREEN to DARK BLUE (+) IGNITION SWITCH HARNESS
IGNITION 2 See NOTE *1
IGNITION 3 N/A
ACCESSORY/HEATER BLOWER 1 WHITE/RED to BROWN (+) IGNITION SWITCH HARNESS
ACCESSORY/HEATER BLOWER 2 N/A
KEYSENSE N/A
PARKING LIGHTS ( - ) BROWN/WHITE (-) @ BCM, GRAY Plug, Pin A7, See NOTE *4
PARKING LIGHTS ( + ) BROWN (+) @ BCM, BLACK Plug, Pin A48, See NOTE *4
POWER LOCK LIGHT BLUE (TYPE B) @ BCM, BLACK Plug, Pin A11, See NOTE *4
POWER UNLOCK DARK BLUE (TYPE B) @ BCM, BLACK Plug, See NOTE *4
LOCK MOTOR WIRE GRAY (+) @ DOOR LOCK SWITCH in DRIVERS DOOR
DOOR TRIGGER See NOTE *2 See DIAGRAM
DOMELIGHT SUPERVISION WHITE to DARK GREEN/WHITE (-) @ BCM, BLACK Plug, Pin A46, See NOTE *4
TRUNK RELEASE N/A
SLIDING POWER DOOR N/A
HORN GREEN to BLACK (-) @ BCM, GRAY plug, Pin A25, See NOTE *4
TACH ANY wire that is NOT PINK or BLACK @ any IGNITION COIL or FUEL INJECTOR
WAIT TO START LIGHT
BRAKE LIGHT BLUE (+) @ STEERING COLUMN HARNESS
FACTORY ALARM DISARM N/A
ANTI-THEFT GM'S NEW PASSLOCK 2 ANTI-THEFT System
NOTES

NOTE *1 This vehicle requires a special PASSLOCK 2 Bypass module Part #XK06 or PLJX

NOTE *2 This vehicle has (4) door trigger wires the GREY/BLACK (-) is used for the DRIVERS door Pin A32, the PASSENGER door is a LIGHT GREEN/BLACK (-) Pin A38, the DRIVERS REAR door is a LIGHT BLUE/BLACK (-) Pin A39 and the PASSENGERS REAR door is a BLACK/WHITE (-) Pin A39 all are located at the BCM's BLACK Plug. When connecting to an ALARM SYSTEM use all 4 and DIODE ISOLATE.

NOTE *4 the BCM is located in the PASSENGER KICK PANEL.